jaf 刷機不成功，也沒刷死…

看到人家刷死成磚…然後救活…真羨慕…
我怎麼都刷不死我的n97…

心臟好大...我還想刷我的小7刷成港版的...
可是看內地那邊刷完一堆問題..就放棄了...

我刷死兩次 = ="

安裝JAF時提示安裝驅動都選否
OVI套件移除
裝NSU
未死機時勾選manual flash、factory set、normal mode、ini
死機時接上USB拔電池 上面多勾選一ㄍdead usb 點flash
看到提示press power on時裝電池 基本上不會失敗


還有妳要用V20以上版本不是ㄇ？
為什麼JAF裡放的待刷韌體是V11的呢？＠＠
N97不能降級 只能平刷或升級刷喔

謝謝指教！我試完再報告！
還有…我的軔体是v11的啦！

妳手機目前是V11的
要升級的話
放在JAF搜尋目錄裡的韌體檔應該是更高版本ㄉ阿
可是如圖 JAF搜尋到的是V11的呢 降就僅僅平刷而已囉
所以記得將更高版的韌體放到對應資料夾喔

JAF 62平台不支持刷97啊
參考來自bbs.dospy.com/archiver/tid-4532983.html

你用USB刷，，还是刷机线。USB很容易死的，，，都是用刷机线搞定的
參考來自www.dospy.com/bbs/archiver/tid-2082324.html


1. 建议换成1.98.64以上版本
2. 换个USB口子试试
3. 装个凤凰，刷一次原版试试，然后在用新版的JAF刷一次原版试试
參考來自www.opda.net.cn/thread-392781-1-1.html

今天晚上刷机时出现Stage 2 starting..后就关机死在那里了，一百度发现不少人有这种情况。塞班里有人仁兄说选dead usb果然有效。
具体方法是：1开机时选择dead usb， 然后点 inf ， 出现要选的固件以后 选好。2 此时关机 ，点 flash 。开始刷机，下面出现搜索手机的提示（英文的,search phone 好像是这么写的 - -!） 此时开机。下面就出现了可爱的绿色进度条了。
遇到此情况的童鞋可以试试
參考來自www.opda.net.cn/thread-367010-1-1.html




以上…尚未成功
最近的一次刷jaf記錄

JAF version 1.98.66 beta5
Detected PKEY: 9000AAC9
P-key nokia module version 01.02
FBUS INTERFACE NOT CONNECTED!!!
USB Cable Driver version: 7.1.23.0
Changing mode...Done!
Detected P-KEY: 9000AAC9
P-key nokia module version 01.02
Init usb communication...
Failed! Aborting!(還沒連手機)
Searching for phone...Detected P-KEY: 9000AAC9
P-key nokia module version 01.02
Init usb communication...(按刷新之後inf)
Found
MCU SW version: V ICPR72_09w17.5
05-06-09
RM-505
(c) Nokia
HW version: 4001
PCI version:
RFIC version:
DSP version:
APE SW Core version: V 11.0.021
APE Variant version: V 11.0.02111.0.02111.0.021
APE Test version: rm505ENOx09w14v0.020
Retu version: 16
Tahvo version: 22
APE HW version: 256
APE ADSP SW version: 256
APE BT version: HCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12708.
Content Pack version: RM505_RM507_002_000_M019

Production serial number: CJM905375
Product code: 0575266
Module code:
Basic production code: 0570816
Flash code:
Order number:
Product specific data:
Long production SN: 0
ATO:
Default SN type:
IMEI plain: 354225039398669
IMEI spare to net: 3A 45 22 05 93 93 68 06
IMEI SV to net: 33 45 22 05 93 93 68 06 F3

LOCK STATUS:

CONFIG KEY: 2440700000000000
Provider: AT&T;U.S.A. (3650)
Key Code count: 0, FBUS Code count: 0

Block 1:
Lock 1: OPEN Lock 2: OPEN Lock 3: OPEN Lock 4: OPEN Lock 5: OPEN
Block 2:
Lock 1: OPEN Lock 2: OPEN Lock 3: OPEN Lock 4: OPEN Lock 5: OPEN
Block 3:
Lock 1: OPEN Lock 2: OPEN Lock 3: OPEN Lock 4: OPEN Lock 5: OPEN
Block 4:
Lock 1: OPEN Lock 2: OPEN Lock 3: OPEN Lock 4: OPEN Lock 5: OPEN
Block 5:
Lock 1: OPEN Lock 2: OPEN Lock 3: OPEN Lock 4: OPEN Lock 5: OPEN
Block 6:
Lock 1: OPEN Lock 2: OPEN Lock 3: OPEN Lock 4: OPEN Lock 5: OPEN
Block 7:
Lock 1: OPEN Lock 2: OPEN Lock 3: OPEN Lock 4: OPEN Lock 5: OPEN

Loading INI list...
Detected P-KEY: 9000AAC9
P-key nokia module version 01.02
Init usb communication...
Reading product code...
Product Code: 0575266
Searching for JAF saved location of ini...
Checking path: C:\Program Files\Nokia\Phoenix\Products\RM-505\

Searching for default location of ini...
Checking path: \Products\RM-505\
Searching for JAF saved location of ini...
Checking path: C:\Program Files\Nokia\Phoenix\Products\RM-505\
Scanning ini files...
Searching for default location of ini...
Checking path: \Products\RM-505\
Checking path: C:\Program Files\Nokia\Phoenix\Products\RM-505\
FILES SET FOR FLASHING:
MCU Flash file: C:\Program Files\Nokia\Phoenix\Products\RM-505\RM-505_11.0.021_prd.core.C00
PPM Flash file: C:\Program Files\Nokia\Phoenix\Products\RM-505\RM-505_11.0.021_prd.rofs2.V25
CNT Flash file: C:\Program Files\Nokia\Phoenix\Products\RM-505\RM-505_11.0.021_C01_prd.rofs3.fpsx
APE Variant file: C:\Program Files\Nokia\Phoenix\Products\RM-505\RM505_507_11.0.021_uda8_001.uda.fpsx
Languages in ppm: English,Chinese S(PRC),Chinese Trad (Taiwan)
Done!
Backing up CRT...(開始刷…目前之移除所有nokia相關的狀態jaf鳳凰與ovi…還重開機)
Detected P-KEY: 9000AAC9
P-key nokia module version 01.02
Init usb communication...
Reading IMEI...
C:\Program Files\ODEON\JAF\ProgData\354225039398669_CRT_backup_188295.pm
Done!
Backup CRT OK!
Detected P-KEY: 9000AAC9
P-key nokia module version 01.02
Init usb communication...
Searching for phone...Found
Reading SW version...ICPR72_09w17.5 11.0.021
Reading battery value...3779 mV
Init usb flashing...
Reading flashid...
CMT: 004000EC ＜=＞ SAMSUNG (SEC) -＞ KAT00F00RA
APE: 00000000 ＜=＞ Flash -＞ not detected
Verifing ADL communication... Status byte 7
Rebooting to flash mode...
Waiting for the phone to reboot...
Searching for phone...
Phone rebooted but not in flash mode...(第一次失敗…手機斷開多次無回應然後無動作)
Searching for phone...Detected P-KEY: 9000AAC9(再inf刷新一次)
P-key nokia module version 01.02
Init usb communication...
Found
MCU SW version: V ICPR72_09w17.5
05-06-09
RM-505
(c) Nokia
HW version: 4001
PCI version:
RFIC version:
DSP version:
APE SW Core version: V 11.0.021
APE Variant version: V 11.0.02111.0.02111.0.021
APE Test version: rm505ENOx09w14v0.020
Retu version: 16
Tahvo version: 22
APE HW version: 256
APE ADSP SW version: 256
APE BT version: HCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12708.
Content Pack version: RM505_RM507_002_000_M019

Production serial number: CJM905375
Product code: 0575266
Module code:
Basic production code: 0570816
Flash code:
Order number:
Product specific data:
Long production SN: 0
ATO:
Default SN type:
IMEI plain: 354225039398669
IMEI spare to net: 3A 45 22 05 93 93 68 06
IMEI SV to net: 33 45 22 05 93 93 68 06 F3

LOCK STATUS:

CONFIG KEY: 2440700000000000
Provider: AT&T;U.S.A. (3650)
Key Code count: 0, FBUS Code count: 0

Block 1:
Lock 1: OPEN Lock 2: OPEN Lock 3: OPEN Lock 4: OPEN Lock 5: OPEN
Block 2:
Lock 1: OPEN Lock 2: OPEN Lock 3: OPEN Lock 4: OPEN Lock 5: OPEN
Block 3:
Lock 1: OPEN Lock 2: OPEN Lock 3: OPEN Lock 4: OPEN Lock 5: OPEN
Block 4:
Lock 1: OPEN Lock 2: OPEN Lock 3: OPEN Lock 4: OPEN Lock 5: OPEN
Block 5:
Lock 1: OPEN Lock 2: OPEN Lock 3: OPEN Lock 4: OPEN Lock 5: OPEN
Block 6:
Lock 1: OPEN Lock 2: OPEN Lock 3: OPEN Lock 4: OPEN Lock 5: OPEN
Block 7:
Lock 1: OPEN Lock 2: OPEN Lock 3: OPEN Lock 4: OPEN Lock 5: OPEN

Loading INI list...
Detected P-KEY: 9000AAC9
P-key nokia module version 01.02
Init usb communication...
Reading product code...
Product Code: 0575266
Searching for JAF saved location of ini...
Checking path: C:\Program Files\Nokia\Phoenix\Products\RM-505\

Searching for default location of ini...
Checking path: \Products\RM-505\
Searching for JAF saved location of ini...
Checking path: C:\Program Files\Nokia\Phoenix\Products\RM-505\
Scanning ini files...
Searching for default location of ini...
Checking path: \Products\RM-505\
Checking path: C:\Program Files\Nokia\Phoenix\Products\RM-505\
FILES SET FOR FLASHING:
MCU Flash file: C:\Program Files\Nokia\Phoenix\Products\RM-505\RM-505_11.0.021_prd.core.C00
PPM Flash file: C:\Program Files\Nokia\Phoenix\Products\RM-505\RM-505_11.0.021_prd.rofs2.V25
CNT Flash file: C:\Program Files\Nokia\Phoenix\Products\RM-505\RM-505_11.0.021_C01_prd.rofs3.fpsx
APE Variant file: C:\Program Files\Nokia\Phoenix\Products\RM-505\RM505_507_11.0.021_uda8_001.uda.fpsx
Languages in ppm: English,Chinese S(PRC),Chinese Trad (Taiwan)
Done!
Backing up CRT...(不怕死再刷一次)
Detected P-KEY: 9000AAC9
P-key nokia module version 01.02
Init usb communication...
Reading IMEI...
C:\Program Files\ODEON\JAF\ProgData\354225039398669_CRT_backup_1812295.pm
Done!
Backup CRT OK!
Detected P-KEY: 9000AAC9
P-key nokia module version 01.02
Init usb communication...
Searching for phone...Found
Reading SW version...ICPR72_09w17.5 11.0.021
Reading battery value...3838 mV
Init usb flashing...
Reading flashid...
CMT: 004000EC ＜=＞ SAMSUNG (SEC) -＞ KAT00F00RA
APE: 00000000 ＜=＞ Flash -＞ not detected
Verifing ADL communication... Status byte 7
Rebooting to flash mode...
Waiting for the phone to reboot...
Searching for phone...
Sending RAW loader...
Using 009.008.003
Elf2flash 09.11.000
CMT RAW loader...
Patching RAW boot step1...
Patching RAW boot step2...
Patching RAW boot step3...
Sending RAW Loader...
....................Loader Sent!
Stage 2 starting...............(目前還停在這…手機充電中…？)



雖然對岸說要用jaf刷diy固件，用鳳凰刷下載軔体，但我沒試過(聽說用鳳凰刷diy一定死機)
現在我還能試什麼呢？

天有不測風雲，人有旦夕禍福…這表示我又沒成功…



我可以了解不死人的感覺
不是不死，而是目前還死不了…

crt308那個選項迷要勾吧？＠＠ 那郭圖上寫小N的設定請刪掉啊！！！免得誤導大眾ㄟ～
該勾的...該做的....在上面我都有回復了

我使用jaf 1.98.62版本
OS是W7-64
使用上迷遇過問題

也幫過版內機友遠端刷機....那位朋友是XP系統
也是成功了....

sorry
最近忙抱怨！
沒空刷說！